服务热线: 15306575657 18248457755
新闻资讯
NEWS CENTER
  • 交联聚乙烯垫复合纳米二氧化硅保温毡保温构造的工艺流程
  • 本站编辑:杭州孚安保温材料有限公司发布日期:2019-12-26 20:32 浏览次数:

交联聚乙烯垫复合纳米二氧化硅保温毡隔音减振垫使用方法:,需要将地面清扫干净,做到无突起物,地面平整其次,铺设减振垫,相接处要整齐密封,如边角不齐,需用刀剪切齐,相接的地方可采取搭接或平接的方式连接,平接则必须用专用胶水将接缝粘牢,接缝处用胶带封严,防止上层混凝土施工时,水泥砂浆渗入减振板下面,造成传声桥再次在4周墙边将隔音垫边缘向上折起,用建筑胶点粘楼板隔音垫于墙面,翻包高度为包括混凝土和面层的总厚度,折起翻包部分接缝也要用胶带粘贴严密较后铺设厚度不小于40mm的C20细石混凝土,混凝土内需配加固钢筋网,楼板隔音减振垫5mm常用,注意钢筋网不得刺破隔音垫,钢筋网保证在混凝土层的中上部铺设厚度不小于40厚的C20细石混凝土,不得用水泥砂浆代替,且C20细石混凝土水含量不宜过大,容易导致开裂选隔音减振板的时候1定要确切根据需求来选择材质,而不是只关注价格,不同的情况下所有的料是不一样的。

2-1Z6191H645.jpg

  想要效果好就应该在材质选择方面科学合理:

  1、高密度发泡阻尼材料,可有效吸收各频率的振动与噪声,针对楼板的撞击声改善量高达1530dB,令建筑分户楼板撞击隔音效果超越现行绿色建筑标准要求,满足或优于5星级酒店水平。

  2、因材料表面的摩擦系数大,铺装后不易移位利于防风与成品保护;产品厚度薄、刚度高,可显著改善各种常见低密度发泡隔音垫产品的脚感效果,彻底空鼓隐患。

  3、适用于30℃-120℃温度环境,对性能不会造成显著影响。

  4、惰性产品,可抗霉菌或真菌的生长5、施工工艺简单、安装快,综合成本低。

Usage of cross linked polyethylene pad and nano silicon dioxide insulation felt: first, clean the ground to ensure no protrusions, and then lay the damping pad. The joints should be sealed neatly. If the edges and corners are not flush, they should be cut with a knife. The joints can be connected by lapping or butt joint, and the joints must be firmly bonded with special glue The joints shall be sealed with adhesive tape to prevent the cement mortar from infiltrating under the damping plate during the construction of the upper concrete, so that the sound bridge will fold up the edge of the sound insulation pad at the wall for four weeks again, and the floor sound insulation pad will be pasted on the wall with building glue points. The turnover height includes the total thickness of the concrete and the surface layer. The joints of the folded turnover shall also be pasted tightly with adhesive tape, and the laying thickness shall not be less than 40mm The C20 fine aggregate concrete shall be reinforced with reinforcing steel mesh in the concrete. The floor sound insulation and vibration damping pad is 5mm in common use. Pay attention that the steel mesh shall not pierce the sound insulation pad. The steel mesh shall ensure that the C20 fine aggregate concrete with a thickness of no less than 40 is laid in the middle and upper part of the concrete layer and shall not be replaced by cement mortar. The water content of C20 fine aggregate concrete shall not be too large, which is easy to cause cracking. When selecting the sound insulation and vibration damping board, it shall be determined We should choose the materials according to the needs, not only the price. Under different circumstances, all materials are different.

To achieve good results, we should make scientific and reasonable material selection:

1. The high density foam damping material can effectively absorb the vibration and noise of various frequencies. The impact sound of the floor can be improved as much as 1530db, which makes the impact sound insulation effect of the building floor exceed the requirements of the current green building standards and meet or better than the level of 5-star hotels.

2. Due to the large friction coefficient of the material surface, it is not easy to shift after pavement, which is conducive to the protection of wind and finished products; the product is thin in thickness and high in rigidity, which can significantly improve the foot feeling effect of various common low-density foam sound insulation pad products, and completely empty the hidden danger.

3. It is suitable for 30 ℃ - 120 ℃, and has no significant effect on the performance.

4. Inert products can resist the growth of mould or fungus. 5. The construction process is simple, the installation is fast, and the comprehensive cost is low.